On a side note, I also added a Ricmotech load cell modification kit to my brake pedal. Firmware driver - Top 4 Download - offers free software downloads for Windows, Mac.I recently upgraded my steering wheel and pedals from a Logitech G27 to a Thrustmaster T500RS with T3PA Pro pedals. 2 large, wheel-mounted sequential paddle shifters 5/13 cm tall 100 metal Tact switch with life cycle exceeding 500,000 activations.Thrustmaster T150 RS Pro Force Feedback Wheel PS4/PS3/PC by. 11/28 cm in diameter, with an ergonomic design perfectly adapted for all racing games (GT, F1, NASCAR, RALLY, etc.) Rubber-coated wheel grips. Realistic competition wheel design.
![]() Tmx Pro Force Feedback Program Update To WindowsClick it, then click Control Panel. In your list of programs, scroll down to Thrustmaster. Click Start or the little Windows icon on the left side of the task bar. Windows keeps trying to hide the control panel from users, and they’ve done a pretty good job of it with the latest update to Windows 10, but there are at least a couple of ways you can get into the settings for your Thrustmaster T500RS.Click Set up USB Game Controllers. Click Settings (the cog or gear icon), then type USB Game Controllers in the search box. Click Start or the little Windows icon on the left side of the task bar. You can update your firmware quickly and easily using that link. Also note that there is a Firmware Update link under Thrustmaster. IRacing will only use 900° of rotation so anything higher is basically ignored. You should occasionally use it to make sure your wheel software is updated.Here on the Test Input tab, you should set your Rotation/Angle to 900° or higher. Thrustmaster T500RS Settings – Test Input TabNote the Check for Update button on the lower right. I found it worked best to simply press hard enough to get the slider to 100% and leave it at that.Next, click the Gain Settings tab. Ricmotech has instructions for calibrating their load cell mod, but they actually didn’t work for me. If you have a load cell modification installed you may have to press pretty hard to get to 100%. If you have a brake mod installed, you should get the brake slider all the way to 100%. Now I’m thinking about trying 40 or 45% because I’ve never really liked a lot of force feedback. I tried it at 55% for a while, then moved it down to 50%. This is really a personal preference and you can change it at any time based on the amount of force feedback you want. IRacing recommends that you set this between 50% and 60%. Thrustmaster T500RS Settings – Gain SettingsLeave all of this at default except the Overall Strength of all forces setting. Now we can move on and get ready to turn some laps in iRacing.So let’s get the iRacing simulation open and running with a good car and track loaded. This is a master gain or strength setting and you will see the value of it later.That’s all there is to configuring the wheel and pedals in Windows. You will also be able to adjust force feedback within iRacing of course, and I’ll have more later on that. When you are instructed to turn your wheel 90° to the left, do it by sight, ignoring the numbers on the screen.Before you begin to calibrate, check the following: Follow the instructions on the screen. Thrustmaster T500RS Calibration in iRacingGo through the calibration procedure beginning with your steering calibration. If you’re using a load cell, it’s important that you calibrate it properly in iRacing.Click Calibrate or click Options to get a window that looks something like the image below. If you’ve already done that, you can skip this or go through part or all of the calibration process again. Any time you change your brake force factor, you should probably recalibrate your pedals. If you don’t have a load cell, you can leave it at about 1.8 or set it to zero, it’s really a personal preference with which you can experiment. If you have a load cell, you must set this to zero. The standard pedal calibration is also very simple and straightforward.If you are using a load cell in your brake pedal, you will have to experiment with the amount of force you want to apply for full 100% brake. Calibrate your Steering first, following the instructions on the screen. Check Use custom controls for this car.If the controller has never been calibrated in iRacing, you will probably have to calibrate it, then go back and change the settings above, then recalibrate your pedals only.Calibration is very straightforward. I recommend setting the Min force to zero for this wheel. I suggest 5 as a good place to start for now. We’ll go over the Strength setting in more detail later. It’s really a matter of personal preference and the cars that you drive. It still takes some force to get the brake to 100%, but it’s not excessive. When I calibrate the brake, I only press hard enough to get the slider between 250 and 300. I tried to use that setting for a while then decided it was too difficult to use that much force, especially with heavier cars like the iRacing Dirt Street Stock or Late Models. I hope you picked a good car and track. How to Set and Save Your Force Feedback For Each Car in iRacingNow it’s time to make a few laps and get your force feedback set properly for your first car. It will require one-time calibration in every car you drive, but it’s worth it in my opinion. If you want to use different force feedback strengths for each car you drive (recommended), you need to have Use custom controls for this car checked in Options. Best video edition software for macIf you made at least two laps you will see auto in the lower right corner. FFB strength is shown at the bottom of the black box. That brings up the Graphics Adjustment black box, shown to the right. Stop on the track without getting out of the car. It’s a little extra effort but it’s worth it.If you have any questions about any of this, feel free to join me in the OSR Discord Server. You will need to go through this process for each car that you drive frequently.
0 Comments
Leave a Reply. |
AuthorWayne ArchivesCategories |